Super-micro-computer X6DHi-G2 Manuel d'utilisateur télécharger pdf (Page 104)

C-14

X6DH3-G2/X6DHi-G2 User's Manual

5. Repeat Step 4 so that both drives to be initialized are selected (as shown in the

screen below).

6. Press Enter.

7. Read the warning message as shown in the screen.

8. Make sure that you have selected the correct disk drives to initialize. If correct,

type Y to continue.

1 2 ... 99 100 101 102 103 104 105 106 107 108 109 ... 119 120

SUPER 1
Preface 3
Table of Contents 4
Chapter 3: Troubleshooting 5
Chapter 4: BIOS 6
Appendices: 6
Chapter 1 7
Introduction 7
Contacting Super Micro 8
Chapter 1: Introduction 9
UPER X6DH3-G2 10
Connector Description 11
Motherboard Features 12
14
1-2 Chipset Overview 15
1-3 Special Features 16
1-4 PC Health Monitoring 16
1-5 ACPI Features 17
1-6 Power Supply 18
1-7 Super I/O 18
Chapter 2 21
Installation 21
To Un-install the Heatsink 24
(installed) 25
2-3 Installing DIMMs 26
http:www 26
DDR 2 Slot 27
Release Tab 27
Front Control Panel 28
2-5 Connecting Cables 29
Serial Ports 34
Chassis Intrusion 34
Universal Serial Bus (USB) 35
ATX PS/2 Keyboard and 36
PS/2 Mouse Ports 36
GLAN (Giga-bit Ethernet 36
Power LED/Speaker 37
Fan Headers 37
Wake-On-Ring 38
Wake-On-LAN 38
Power SMB (I 39
C) Connector 39
Overheat LED (JOH) 41
Power Supply Failure LED 41
2-6 Jumper Settings 42
Watch Dog Enable 43
CMOS Clear 43
VGA Enable/Disable 44
Alarm Reset (JAR) 44
3rd PWR Supply PWR Fault 45
Detect (J3P) 45
SAS Controller Enable (*For 45
Power Force On Enable/ 46
2-7 Onboard Indicators 47
Adaptec SAS Activity LED 48
Indicators (For the X6DH3 48
Parallel 49
Floppy Connector 50
IDE Connectors 51
Chapter 3 53
Troubleshooting 53
Memory Errors 54
Chapter 4 57
4-2 Running Setup 58
4-3 Main BIOS Setupʳ 58
Main BIOS Setup Menu 59
Multi-Sector Transfer 61
LBA Mode Control 61
32 Bit I/O 61
4-4 Advanced Setup 62
Processor Power Management 69
Hardware Monitor Logic 73
CPU Temperature Threshold 73
4-5 Security 74
Set User Password 75
Fixed Disk Boot Sector 75
Password on Boot 75
4-6 Boot 76
4-7 Exit 77
Appendix A 79
BIOS POST Messages 79
Appendix B 85
BIOS POST Codes 85
POST Code Description 86
Appendix C 91
The Enhanced Mode: 92
The Combined Mode: 92
RAID 1 Init 99
Initializing Disk Drives 102
Rebuilding Arrays 105
Managing Arrays 107
Deleting Arrays 108
*Warning 108
Creating Arrays 108
Assigning Array Properties 109
Adding a Bootable Array 110
Using the Disk Utilities 115
Operating System 117
ATA RAID Controller Driver 118
Supero Doctor III 119

Commentaires sur ces manuels

Pas de commentaire

Super-micro-computer X6DHi-G2 Manuel d'utilisateur Page 104

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Super-micro-computer X6DHi-G2